@topos-protocol/topos-playground v0.2.0

Getting Started

The Topos Playground is a CLI that allows you to easily run and manage a local Topos devnet. It depends on Docker and NodeJS, and manages a number of components in order to locally run multiple subnets, multiple TCE nodes, and a dApp with supporting infrastructure, capable of cross-subnet messaging. For additional information about Topos and about this Playground CLI, take a look at the Topos Developer Portal.

Requirements

• Docker version 17.06.0 or greater
• Docker Compose version 2.0.0 or greater
• NodeJS version 16.0.0 or greater
• Git

Install / Run topos-playground

Depending on your NodeJS environment and preferences, there are several ways to install the Topos Playground.

To install the playground globally, using npm, run the following command:

$ npm install -g @topos-protocol/topos-playground

To install the playground globally, using yarn, run the following command:

$ yarn global add @topos-protocol/topos-playground

Alternatively, you can install and run via npx:

$ npx @topos-protocol/topos-playground

Install via Git

If you prefer to install the playground via Git, you can clone the repository and install it manually.

$ git clone https://github.com/topos-protocol/topos-playground.git
$ cd topos-playground
$ npm install
$ npm run build && npm link

Run the CLI

If you have installed the via npm, yarn, or manually after building it from the git repository, you can run the CLI like any other command line tool:

$ topos-playground --help

If you are using npx, you will run it via npx:

$ npx @topos-protocol/topos-playground --help

Topos Playground supports two subcommands, start and clean.

$ topos-playground start

This will check that the required prerequisites are met, and will then setup and start all of the containers for a complete local Topos network. It will report progress to the console as well as logging to a file.

$ topos-playground clean

To clean up any still-running docker containers or filesystem artifacts from a previous invocation of the topos-playground, use the clean command.

The playground respects XDG Base Directory Specifications, so by default, it will store data used while running in $HOME/.local/share/topos-playground and it will store logs in $HOME/.state/topos-playground/logs.

To override these default locations, you can set your HOME, XDG_DATA_HOME and XDG_STATE_HOME environment variables, or specify them in a .env file.

$ HOME=/tmp topos-playground start

By default, topos-playground sends output to both your console and to a log file when it is running. To disable this, you can use the --quiet flag to prevent output from going to the console, or the --no-log flag to prevent output from going to the log file.

$ topos-playground clean --quiet

For more in-depth discussion about the playground components, and what the topos-playground is doing, take a look at the Topos Playground components portion of the Topos Developer Portal.

Development

To contribute to the development of the playground, fork the repository.

Do your work within a branch on your fork. When it is ready, create a Pull Request that clearly explains the reasoning behind your code changes, what they do, and anything that we should be aware of when testing your code.

Discussion

For community help or discussion, you can join the Topos Discord server:

https://discord.gg/zMCqqCbGMV

Troubleshooting

• Running the redis server...❗ Error

The container that provides the Redis service was unable to start. This is likely because you are already running a Redis instance on your system. Try shutting it down.

On Linux:

$ sudo systemctl stop redis-server

or

$ sudo service redis-server stop

On MacOS:

brew services stop redis

If you manually installed and started Redis, you will need to manually stop it.

$ redis-cli shutdown

• docker: Error response from daemon: Conflict. The container name "/redis-stack-server" is already in use by container "1ccdeb3adf2259168a5f74697013eaab8d61fb18e123e0a4d06545ac4269cc94". You have to remove (or rename) that container to be able to reuse that name.

This error indicates that the redis-stack-server container is already running. This is likely because you have already ran the playground, but a topos-playground clean was never ran. To fix this, run topos-playground clean and then try again.

This may also sometimes occur if you have a local redis instance running. Refer to the instructions above for how to shut down a local redis instance.

• Error: service "contracts-incal" didn't complete successfully: exit 1

One cause of this error is a previous failure when starting the playground that wasn't cleaned up by running topos-playground clean. To fix this, run topos-playground clean and then try again.

• Error: info: unknown shorthand flag: 'd' in -d

If you see this error, you likely do not have Docker Compose installed. You need version 2 or greater. Refer to the Docker Compose installation instructions for your platform.

• Error: failed to create network local-erc20-messaging-infra-docker: Error response from daemon: could not find an available, non-overlapping IPv4 address pool among the defaults to assign to the network

The likely cause of this error is that you are running a VPN of some sort.

The quick fix for this is to shut down your VPN, and then try to run the playground again.

• Error: Cannot connect to the Docker daemon at unix:///var/run/docker.sock. Is the docker daemon running?

If this error occurs, it likely means that your dockerd daemon is not running. Please consult the documentation for your OS and Docker installation to determine how to correctly restart it for your platform.

• Error: Error response from daemon: driver failed programming external connectivity on endpoint infra-tce-boot-1 (145130455efa244316eb0570064adb584e2c99d18fa2cd8f58b2774f1144d2bb): (iptables failed: iptables --wait -t nat -A DOCKER -p tcp -d 0/0 --dport 32807 -j DNAT --to-destination 172.21.0.9:9090 ! -i br-de97b637b33b: iptables v1.8.7 (nf_tables): unknown option "--to-destination"

If this error occurs, you are running Linux, and you have recently done an OS upgrade, try rebooting your system. If the problem persists, first ensure that you can load the 'xt_nat' kernel module:

$ sudo modprobe xt_nat

If that command fails, then this is likely the problem. You can try to load the module manually:

$ sudo insmod /lib/modules/$(uname -r)/kernel/net/netfilter/xt_nat.ko

And then try again.

If that command succeeds, but the problem persists, check your iptables version:

$ iptables --version

It should show something like this:

iptables v1.8.7 (nf_tables)

If the nf_tables is absent, and you have already tried to reboot, investigate your /usr/sbin/iptables symlink. It should point to /usr/sbin/xtables-nft-multi. It should, either via a direct link, or perhaps through a chain of symlinks, point to /usr/sbin/xtables-nft-multi.