internal-dns v0.2.0

Purpose

Everyone in your office tests out sites on their own computer.

Maybe you've tried visiting a site on a coworker's computer, by IP address.

Maybe you've even figured out how to use DHCP client IDs to give them a hostname on the local network. But that doesn't help you reach the right virtual host on their computer.

What if everyone could have their own subdomain, so that jane.punk, site1.jane.punk and site2.jane.punk all resolved to the same laptop?

That's what internal-dns gives you.

Install

Step One: install the dnsmasq service on your Linux server.

Under Ubuntu Linux that would be:

apt-get install dnsmasq

Make sure your system is set to start it on every boot.

Now install internal-dns:

npm install -g internal-dns

Step Two: create /etc/internal-dns.js and populate it with your settings. Here's a typical configuration:

module.exports = {
  // Include these custom lines in /etc/dnsmasq.conf. These two
  // are recommended, see the dnsmasq manpage
  dnsmasq: [
    'domain-needed',
    'bogus-priv'
  ],
  // Specify the range of IP addresses you want to assign
  // *statically* to individual coworkers, granting them domains
  //
  // Supports only ipv4 so far
  staticRange: {
    low: '10.1.10.1',
    high: '10.1.10.100'
  },
  // Specify the range of IP addresses you want to assign
  // *dynamically* to everyone else
  //
  // Supports only ipv4 so far
  dynamicRange: {
    low: '10.1.10.101',
    high: '10.1.10.254'
  },

  // This way "jane.mycompany" or "site.jane.mycompany" both
  // will point to Jane's computer. DON'T add .com, this is
  // meant for internal use on your LAN.
  domain: 'mycompany'
};

If /etc/internal-dns.js is an unacceptable location for you, you can use the -c option to specify an alternate configuration file every time you launch internal-dns.

Step Three: start adding your coworkers' computers by name. These should be valid hostnames (letters, digits and dashes; TODO: support unicode) and should not contain periods.

NOTE: once you begin doing this, dnsmasq will be up and running, if it wasn't already.

internal-dns add jane janes.mac.address.here
internal-dns add joe joes.mac.address.here

You can also remove a user:

internal-dns remove joe

You can remove an entry by mac address as well, just use the mac address instead of the name.

To update a user, just use the add command again. Any existing entry for that name or mac address will be updated rather than duplicated.

Step Four: shut off the DHCP service on your router.

Testing

dnsmasq is now your DHCP and forwarding DNS server, handing out IP addresses to computers based on their hardware address (mac address) and answering questions about local names like site.jane.mycompany directly.

You will want to try renewing your DHCP release manually to see if you are assigned an IP in the staticRange you configured.

After that, if you added your computer with internal-dns add jane mac-address, you should be able to visit site.jane.mycompany and talk to the website you're testing on your computer.

Other options

By default, internal-dns stores information in /var/lib/internal-dns.json. You can change that with the json option. A lockfile with a .lock extension is always created in the same folder.

By default, internal-dns writes a valid configuration to /etc/dnsmasq.conf. You can change this location with the conf option, if you have set up dnsmasq differently.

By default, the timeout for DHCP leases is 2 hours. You can change that with the timeout option, which defaults to 2h.

By default, dnsmasq is stopped with the command service dnsmasq stop, and started with the command service dnsmasq start. You can change that with the start and stop options.

By default, internal-dns scans /var/lib/misc/dnsmasq.leases and removes any existing lease for a mac address that has just been added or removed. This is the right location at least in Ubuntu Linux. However, you can set the leases option to false to completely block this behavior, or set it to a filename if your copy of dnsmasq keeps leases in a different place.

Other commands

You can rebuild dnsmasq.conf without making any changes, which is useful if you edited /etc/internal-dns.js:

internal-dns refresh

Credits

internal-dns was created to facilitate our work at P'unk Avenue.

Changelog

0.2.0: oops, we need separate staticRange and dynamicRange options. It turns out dnsmasq is not clever enough to avoid static addresses when handing out dynamic addresses. This lead to IP address conflicts and the occasional machine being locked out of the network entirely. The solution is to configure non-overlapping staticRange and dynamicRange options with 0.2.0. You may need to remove your existing dnsmasq leases file as well as mopping up addresses in /var/lib/misc/internal-dns.json that fall outside your new staticRange, if any.